compressore limiter, usato negli studi di registrazione, alimentazione 220V - Music Corporation

General Guidelines on the use of the Compressor/Limiter:

Thank you for purchasing the Carl Martin Compressor/Limiter!   We believe this unit to be the most musically useful guitar dynamics processor on the market. It has been developed to incorporate the same features, sonic clarity, quietness, and performance of the best studio compressor/limiters. Spend a little time with us here in the manual and you can learn some of the basics of compression and limiting, and how to get the most out of your pedal.

Simply put, compression and limiting may be defined as the active control or modification of the dynamics of an audio signal.

Dynamics may be described as the loudness characteristic of an instrument: the way the note begins, sustains, and ends. Every instrument has dynamics; for example, a guitar has a very strong initial attack and a

The four controls on the Compressor/Limiter are:

THRES, or Threshold, sets the level at which the compression starts to take effect. The higher (clockwise) you set this control, the harder you must play before compression starts to occur. The lower (counterclockwise) you set this control, the sooner compression starts to occur, and can be audible even when playing softly.

COMP or Compression sets the ratio of compression that will be applied to your signal. The ratio, in conjunction with the THRES setting will determine how hard, or how gently, the compressor will affect your signal. Turning the COMP knob clockwise increases the ratio, giving you more compression, while turning it counterclockwise lowers the ratio, giving you a softer effect. There are no right or wrong settings for the ratio, or any other control on a compressor for that matter. It is entirely an artistic choice, based upon what you want to hear.

RESP or Response determines the way the compressor responds to your playing. In full clockwise position the unit acts as a peak-limiter, providing a simple "brick wall" attenuation (reduction of the signal) when the signal reaches the point you have set on the THRES knob. The more you turn the RESP knob counter clockwise, the more the unit acts as a modern compressor with signal-dependant attack and release times. In simple terms, If you like a more effected sound, where you can clearly hear the compressor actively shaping your sound, you want more of a compressor response (RESP more counter-clockwise), if you want a limiting function you want the RESP knob more clockwise.   

This is set for a very active, signal-dependant compressor function. As you play, turn the THRES knob counter-clockwise, and you will see how quickly the compression starts to occur, and how strongly it interacts with your playing.

This is more of a fixed-point limiting function. As you play, turn the THRES knob counter clockwise, (you will have to turn it further than with the RESP knob set as in figure 3) and you will hear the unit start to effect the signal.   

Spend some time playing with the THRES and RESP knobs in various places, leaving the other knobs alone for now, and you will see the different kinds of responsiveness available to you. As you become familiar with the pedal, you will find just the settings you are looking for. Of course, the COMP settings will make a difference in all cases, but to keep things simple, it's good to start with the COMP set as in figures 3 & 4.

GAIN is also called "make-up gain", and that is because the more you compress the levels, the softer the signal becomes and this control allows you to compensate for this. By the way, "Gain" is simply a more precise, scientific-term for "volume" or "level" so there is nothing mysterious about this control. Switch the pedal in and out with the footswitch and adjust this knob as needed. You can also use it to get a bit of boost for a solo. If you use single-coil pickups, you will notice that extreme compression settings will accentuate the hum and noise from these pickups. That is simply the nature of compression and single coil pickups, not a function of the pedal, and all compressors exhibit this trait. If you have humbuckers, or you stand where there isn't much hum pickup, you will quickly notice the extreme quietness of this pedal. It really does perform very much like a high-end studio unit.

The "Busy Light" simply tells you how much compression is being applied to your signal. The brighter it gets, the more compression.
Ok, to start out, let's try a good, basic "fattening" sort of compression. This is what engineers often do to your signal in the studio, so you will generally find this a familiar and musically useful sound. To begin with, use these settings:

Adjust the THRES control counterclockwise until you start to hear the compression effect and the Busy light starts lighting up. Adjust the gain as needed.

Now, leaving the THRES control where you can hear the effect, start adjusting the COMP control:

You will notice that the compression becomes harder and more abrupt, giving you more of a "squashed" sound.

Now, leaving the COMP control about here, and the RESP control here:

and the threshold set where you can hear the compression working, start adjusting the RESP control. Here is where the long, singing, sustain sounds may be found.

y the time you have modified your dynamics to this extent, a plot of your signal would look something like this:

SPECIFICHE:

Power:
Power consumption:
S/N ratio:
Input impedance:
Output impedance:
THD distortion:
Threshold range:
Compression range:
Responce range:
Gain range:
Dimension:
Weight:

100 or 115 or 230 VAC 50-60Hz
2,4 Watts
105dB (clean out)
1M Ohm
200 Ohm
0,05%
60 dB
from 1:1 to 1:00
from 125 mS to 12,5 mS
+-20 dB
120(D) 95(W) 77(H)
0,625Kg