combinatore di effetti prima serie - Music Corporation

Cerca
Vai ai contenuti

Menu principale:

combinatore di effetti prima serie

prodotti > carl martin > controller

Octaswitch

L'Octaswitch è come il suo cugino Combinator 2 ma non ha 3 banchi di programmazione, non alimenta otto pedali a 9 volts, non è alimentato a 220 volts.Consente di mettere a loop 8 unità


Example on normal single amp operation


Example on mono dual amp oper


Example on dual amp/stereo operation

Use a Y-cable from the stereo unit to loop 8 return, left on ring and right on tip of the stereo jack. Please notice that there is only full stereo operation with signal on the right output when there is a stereo pedal in loop 8, and loop 8 is engaged i.e. a stereo chorus, to maintain output on both L/R also without the chorus effect, you have to bypass the effect on the chorus pedal.

When there is no stereo pedal engaged there is no signal at the right output.

Example on mono operation with mute and tuner out

Connect a tuner to i.e. loop 2 send, and nothing in the loop return, select i.e. program 8 with only loop 2 engaged, this way you mute the system while getting signal to your tuner, without the signal passing through the tuner.


Example on operation with some pedals going front in the amp, and some in the amp's own loop

As shown on the illustration in this example we do have 4 pedals going to the amp's input, and three pedals in the amp's own loop.
So in the example we use LOOP 5 as the split loop (any can be used) loop 5 send goes the the amp's input, so loop 1-2-3-4 are all front in. The amp's own loop send goes the loop 5 return, and the Octa-Switch main out (left) goes to the amp's loop return, so loop 6-7-8 all will be inserted in the amp's loop after the pre-amp.
IMPORTANT LOOP 5 SHALL ALWAYS BE ACTIVATED.

E' dotato di un buffer opzionale inseribile attraverso uno switch

Si programma con dei micro switch posizionati su ogni canale

Ha una uscita stereo

E' alimentato da 2 pile da 9 volts o attraverso unità esterna tipo Big John o altro, è dotato di uno switch di on/off

Ha un loop stereo e precisamente il numero 8

Ok, so you have eight effects pedals which you use regularly.  You use various combinations of these pedals in various songs, but you are not good at tap dancing…or you are just clumsy and have stepped on the ultra tricked out-metalized-distortion pedal for the lead in your one ABBA cover.  You have seen the digital effects controllers they use on the big stages and have secretly yearned for one, even though you may never make the big stage?  Enter Thomas Guldmann’s Octa-switch.  Your eight effects plug into the eight effects-loops on the back of this unit (all true-bypass, impedance free gold relays so you can run any of your pedals, new and old without problem), and then by turning on or off the numbered switches in each of eight DIP Bank switches, you determine which effects you wish to use simultaneously in each Bank. There is a blue LED for every effects loop used and for each Bank (so once you are programmed, when you step on Bank 6 you will see the lights of all the effects you have assigned to Bank 6 and the Bank 6 LED).  Once you have each Bank programmed, we recommend placing a piece of scotch or electrical tape over each DIP (….just to protect the switch from damage or floods….like beer).  There is a buffered (or not….switchable) Mono input and a stereo Output, and the unit is powered by dual 9v batteries, or by a regulated power supply (we recommend the Carl Martin Big John Power Supply.

SPECIFICHE:

Size:
Weight:
Power:



510x135x55mm
2,3Kg
2x9V, Battery life aprox. 20 hours with average use, it can be used with external supply 9-12V regulated.
Torna ai contenuti | Torna al menu